Termékek pvc gyanta gyártó (23)

Nuancier HELIOS pour tous nos produits en PVC : - fenêtres; - portes d’entrée ; - portes coulissantes

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Together with the Fachhochschule Münster – University of Applied Sciences we are working on ALWA PERM (patent No. 2583995). This is a metal-filled casting resin for producing a porous, resin-bound mould. These materials are applicable in the areas of thermoforming, the ceramic industry, intake moulds and devices, pneumatic cushioning, the filter industry, etc. ALWA PERM allows a castable production of porous metallic materials with a binder for the first time. The system offers a highly accurate mould surface reproduction. The profile characteristics goes far beyond the current state of the art. NO MORE DRILLING OF VACUUM HOLES! NO DAMAGE OF THE MOULD SURFACE DUE TO DRILLING HOLES

COMPOSITION ET ASPECT Blanc & incolore. CARACTÉRISTIQUES TECHNIQUES • Temps de formation de peau : environ 10 minutes (23°C, 50 % HR) • Temps hors poussière : environ 20 minutes (23°C, 50 % HR) • Allongement à la rupture: 150 % • ÉPAISSEUR polymérisé : en 24 h (23°C, 50 % HR) 3 mm • Température d’application : + 5°C à + 40°C CONDITIONNEMENTS Cartouche de 310 ML. STOCKAGE 18 mois à l’abri du froid et des fortes chaleurs en emballage d’origine non entamé. PRÉCAUTION D'EMPLOI Éviter le contact avec la peau. En cas de contact avec les yeux, laver immédiatement avec de l’eau et consulter un spécialiste. Conserver hors de portée des enfants. PRÉPARATION DES SUPPORTS Les supports doivent être propres, secs, sains, dégraissés et dépoussiérés. Ne pas utiliser sur support basique (maçonnerie, béton, marbre...). APPLICATION Étant donné la diversité des supports sanitaires acryliques, un essai de convenance préalable est nécessaire. Lisser à l’eau savonneuse, serrer...

"very strong adhesion to the sub-material high resistance to UV rays toxicologically harmless with normal use Vibration-inhibiting when used in the machine area Millions of people hold plastic products in their hands every day without being aware of this fact. Regardless of whether they are used on sports equipment, medical equipment or work equipment: What is certain is that the pleasant haptic impression - the ""experience of access"" - is an important purchase criterion for the buyer, along with design and functionality. "

IRIS is an acrylic cement paint, for interior and exterior use based on acrylic resins. It is recommended for building surfaces such as concrete, plaster, bricks, etc. It has a highly whitening and covering effect and it is also protective against humidity, high temperature and heavy weather conditions.

Gomastit 407 is a sealant based purely on silicone for joints in the natural stone and parquet area, as well as for connections of various construction materials. Gomastit 407 is mouldresistant, as well as UV and weather resistant. This product is easy to process and ensures durable sealing. Gomastit 407 is mechanically resilient and can be walked on. Usage:Facades, Sanitary, Interior construction, Floor

Résine verte spécialement conçue pour nos applications de fixations chimiques de surface, inventé par la SNIT.

Eine industrielle Bodenbeschichtung, die dank ihrer Epoxidharz-Basis enorm chemikalienbeständig ist. In vielen Farben und den Versionen Säureresistent, Anti-Rutsch, Kalttrocknend, Rapid verfügbar.

White transparent waterproof glue is suitable for waterproofing of absorbent surfaces such as basements, bathroom floors and walls, kitchens, and balconies. It is also suitable for waterproofing of various concrete and masonry structures, as well as for kitchens, bathrooms, balconies, basements and other building parts. Waterproofing Project. It can not only solve the water seepage problem in home life, but also make home life more secure and comfortable. 1kg/barrel 2kg/barrel 5kg/barrel 10kg/barrel 15kg/barrel 20kg/barrel

Die Entscheidung für das richtige System Anforderungen an Böden durch zahlreiche Bewegungs- und Herstellprozesse sowie Beanspruchungen durch Chemikalien kann man häufig nur durch den Einbau einer Kunstharzbeschichtung bzw. eines Kunstharzbelages begegnen. Zudem greifen oftmals rechtliche Vorschriften, die den Einbau einer/eines Kunstharzbeschichtung/-Belages fordern. Bei der Auswahl eines geeigneten Systems sind insbesondere folgende Parameter zu berücksichtigen: • Anforderungen an die Pflege und Reinigung • Langlebigkeit • Forderung einer Rutschhemmungsklasse • Forderung nach Rissüberbrückung • optisches Erscheinungsbild, Farbgestaltung • Forderung nach Ableitfähigkeit • Anforderungen an eine Nichtentflammbarkeit • Lebensmittelneutralität • Anforderungen an die chemische Beständigkeit Lassen Sie sich durch uns individuell zu dem für Sie erforderlichen System beraten.

Acrylic copolymer is an emulsion-based, matt-looking, economical inner surface topcoat paint. It has dull and smooth appearance. It adheres perfectly to surfaces and does not cause any swelling or flaking. It has high breathing capacity.

Pardoseala epoxidica cu granule colorate Emex Quartz - See more at: http://www.e - Pardoseala Epoxidica Decorativa EMEX QUARTZ este un produs profesional, pe baza de rasini epoxidice fara solvent, disponibil intr-o gama infinita de modele obtinute prin inglobarea de granule de cuart sau marmura divers colorate in masa pardoselii. Acest tip de pardoseala se mai numeste si covor epoxidic. Produsul poate inlocui cu succes mozaicul sau gresia, avand in primul rand avantajul aspectului superior, dar fiind si o alternativa mult mai rezistenta atat la utilizare dar si in timp a acestora. Caracteristici principale: - Produs agrementat sanitar; - Aderenta excelenta la suport; - Etalare de exceptie; - Duritate excelenta; - Durabilitate mare; - Rezistenta mare la abraziune; - Rezistenta excelenta la uzura; - Rezistenta mare la agenti corozivi; - Rezistenta mare la hidrocarburi, medii acide sau alcaline.

Glosser paint is intended for decorating the surface of confectionery and bakery products, desserts, fruits, etc. Gives the surface a glossy mirror finish. Great for highlighting decorative elements, allows you to make accents when decorating the appearance of products. Depending on the number of layers applied, it allows you to adjust the color saturation of the coating.

Suitable for universally usable refurbishment wax for mending surface damages and small defects in varnished, oiled or glazed wood surfaces indoors, such as doors and furniture, wall panels and wood parts.

50.5002.00 - PVC-Kleber

Unsere Farbkonzentrate für Kunstharzanwendungen sind in allen RAL Farben für EP, UP, MMA und PUR erhältlich. Diese Pigmentmischungen sind hochkonzentriert und erlauben eine preisgünstige Einfärbung bei problemloser Handhabung. Das an der RAL-Farbskala orientierte Sortiment enthält fast alle RAL-Töne und ist für die Einfärbung von EP, UP, MMA und größtenteils für PUR geeignet. Anwendungsgebiete: Die Farben sind für alle üblichen Anwendungen dieser Harze geeignet, wie z. B. für Fußbodenbeschichtungen, für die Herstellung von Laminaten, Ummantelungen, Gießteilen und Polymerbeton. Dieses Farbsortiment ist bewusst auf reinen Pigmentmischungen aufgebaut, die kein – oftmals störendes – Bindemittel enthalten und dadurch auch sehr farbstark eingestellt werden können. Unsere Kunstharzfarben sind hochkonzentriert bei optimaler Pigment- volumeneinstellung und erlauben so günstigste Einfärbung bei problemloser Handhabung.

Le glaçage Crystal fait partie de notre gamme de glaçages à chaud et offre une couverture complète sur toutes les formes ! Prêt à l'emploi après avoir été chauffé à 40-50°C (en fonction de la viscosité idéale pour l'application souhaitée), sans ajout d'eau. Ce glaçage ne fait pas de bulles et peut être utilisé dans de nombreuses applications pour une finition parfaite des gâteaux. - Brillance parfaite - Totalement translucide - Facile à couvrir toutes sortes de formes - Bonne tenue après application (quelques jours jours au réfrigérateur) - Peut être chauffé directement au micro-ondes ou à la poêle (pas besoin d'eau) - Stable à la congélation/décongélation - Prise rapide au réfrigérateur - Facile à colorer et à aromatiser (Bakbel Flavouring Compound) colorant alimentaire et de l'arôme (Bakbel Flavouring Compound Bakbel) - Peut être réchauffé et réutilisé Caramel, Chocolat, et Neutre.

Starre- und flexible Dichtungsschlämme mit mineralisierenden Eigenschaften

Hochelastischer Silikon-Dichtstoff mit sehr guter Haftung auf nahezu allen bauüblichen Untergründen und Materialien Ideal für Anschluss- und Dehnungsfugen im Bau- und Montagebereich, z. B. an Balkonen, Terrassen und Fenstern (Metall-, Holz- oder Kunststoffrahmen) sowie für Abdichtungen zwischen Beton- und Fassadenbauteilen. Neutralvernetzend (Alkoxy) Sehr gute Haftung auf vielen Baumaterialien Dauerhaft elastisch Nicht korrosiv gegenüber Metallen Schnelle Hautbildung und Durchhärtung Geruchsarm UV- und witterungsbeständig Inhalt: 300 ml EN 15651-1: F-EXT-INT-CC EN 15651-2: G

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Transparent wood preservative, effective against micro organisms, bacteria fungi and algue. It is proposed for the long-time protection of every type of wood. It does not create a film, thus, it does not crack, shell or create a scale. PACKAGE:0,75 LT, 2,5 LT

Acrylic copolymer is an emulsion-based, silicone-folded, textured, thick-grained exterior wall coating material. It adheres very well to surfaces, does not crack and flake, and does not fade. It ensures that the moisture on the wall is expelled with its ability to breathe with its waterproof properties.